U-PROX WDC

Універсальний бездротовий датчик відкриття для дверей та вікон

Використання в приміщенні та на вулиці
Вбудований датчик температури
До 5-ти років автономної роботи
Автоматичне оновлення (OTA)
Три кольори корпусу
Виявлення відкриття дверей/вікон
Можливість підключення сторонніх датчиків

Найшвидший спосіб контролю

Галерея

Фото та відеоматеріали

Сертифікати

Зустрічайте новий продукт!

Гнучке керування системою, миттєві сповіщення та основні функції допоможуть підняти
вашу безпеку та комфорт на новий рівень

Want to buy?

Contact partner companies to purchase or install security and automation devices.

Want to sell?

Become an official distributor, reseller or installer of U-PROX security and safety systems.

Характеристики

Reed switches поріг 7-15 мм,
більше 1 000 000 спрацювань
Power 3V, CR123A
літієва батарея в комплекті
Service life of battery до 5-ти років
Radio frequency Бездротовий інтерфейс ISM з кількома каналами:
ITU регіон 1: 868.0...868.6 МГц (EU, UA), 869.0...869.4 (MA), смуга 100 кГц, 20 мВт макс., відстань - до 4800м (на відкритому просторі);
ITU регіон 3 (AU): 916.5…917 МГц, смуга 100 кГц, 20 мВт макс., відстань до пристроїв - до 4800 м (на відкритому просторі).
Двостороння, шифрована, з визначенням саботажу (глушіння).
Ключ шифрування - 256 біт
Operating temperature range -20°C ... +50°C
Permissible humidity до 95%
III (по EN 50131-1)
2
Dimensions 85 х 20,9 х 20,4 мм
85 х 11 х 6 мм
Case colour білий, чорний, темно-коричневий
Weight 66 грамів
Security grade IP55
Complete set 1. U-Prox WDC;
2. Магніт;
3. Батарея CR123A (попередньо встановлена);
4. Комплект для монтажу;
5. Короткий посібник користувача
Color
+5

U-PROX WDC User manual

Дана інструкція описує порядок встановлення та налаштування бездротових магнітоконтактних сповіщувачів U-Prox WDC. Перед використанням пристрою слід уважно вивчити цю інструкцію.

Технічна підтримка всієї продукції торгової марки U-Prox надається за телефоном та/або за адресою електронної пошти вказаному на сайті u-prox.systems

Застереження щодо безпеки

УВАГА. ПРИЛАД МАЄ ВБУДОВАНИЙ ЕЛЕМЕНТ ЖИВЛЕННЯ. ЗАМІНА ЕЛЕМЕНТА ЖИВЛЕННЯ НА ІНШИЙ НЕКОРЕКТНОГО ТИПУ МОЖЕ ПРИЗВЕСТИ ДО ПОЖЕЖІ АБО ВИБУХУ. УТИЛІЗУЙТЕ ВИКОРИСТАНІ ЕЛЕМЕНТИ ЖИВЛЕННЯ ЗГІДНО З МІСЦЕВИМИ ЗАКОНАМИ ТА ПРАВИЛАМИ

Опис та принцип дії

U-Prox WDC – охоронний точковий магнітоконтактний радіоканальний сповіщувач, призначений для контролювання стану конструктивних елементів на відкриття або зсув для виявлення спроби проникнення до приміщення і для видавання сповіщення про тривогу до центру охоронної сигналізації U-Prox.

Сповіщувач працює лише з охоронною системою U-Prox, під’єднання до сторонніх систем не передбачено.

Має герметичний корпус і застосовується для захисту дверей та вікон.

Прилад має контакти для підключення світлодіоду інформування про постановку під охорону та зовнішнього датчика, наприклад, геркону.

Функціональні елементи пристрою

  1. Нижня пластина корпусу магніту
  2. Кришка корпусу магніту
  3. Неодимовий магніт
  4. Нижня пластина корпусу сповіщувача
  5. Верхня кришка корпусу і капсула з пристроєм
  6. Відмітки розташування магніта
  7. Світлодіодний індикатор
  8. Захисна пластикова пластина з платою пристрою
  9. Тампер-контакт
  10. Роз’єм для підключення:
    • Контакт LD (+ світлодіода, червоний) – універсальний вхід/вихід
    • Контакт GND (земля, синій)
    • Контакт DC (геркон, жовтий)
  11. Кнопка ввімкнення / вимкнення
  12. Елемент живлення, батарея CR123A
  13. Датчик (Геркон)
  14. Світлодіод (LED)
  15. Гумовий ущільнювач

Живлення

Прилад використовує літієвий елемент живлення типу CR123A, що дозволяє йому працювати до 5-ти років на одному елементі живлення.

Індикація в поточному режимі

Світловий індикатор відображає передачу даних та спрацювання датчику.

Обмін даних з охоронним центром, послідовно засвічуються світлодіоди:

  1. Спрацювання чи відновлення датчика – червоний
  2. Передача даних:
    • Зелений – передача успішна
    • Червоний – передача даних не успішна
  3. Прийом підтвердження
    • Зелений – прийом успішний
    • Червоний – прийом даних не успішний

Пункти 2 та 3 можуть бути повторені до 3-х разів (переповтори передачі зі збільшеною потужністю)

Встановлення

Вибір місця встановлення

Ретельно обирайте місце встановлення пристрою U-Prox WDC. Прилад не можна розміщувати:

  1. На вулиці або в приміщеннях з неприпустимою вологістю і температурою
  2. У місцях з високим рівнем радіоперешкод
  3. Поблизу предметів, що можуть викликати затухання або екранування радіосигналу (метал, дзеркала тощо)
  4. На відстані ближче 1 м від центру охорони

Рекомендується виконувати встановлення в наступній послідовності:

  1. Реєстрація датчика в охоронній системі за допомогою додатка U-Prox Installer
  2. Вибір місця встановлення з оптимальним сигналом за допомогою додатка U-Prox Installer. Зважайте, що сповіщувач можна розміщати або вертикально або горизонтально
  3. Встановлення магніта
  4. Встановлення нижньої пластини сповіщувача
  5. Встановлення приладу

Монтаж

УВАГА! ВСТАНОВЛЕННЯ МОЖЛИВЕ НА ДВОСТОРОННЮ КЛЕЙКУ ЛЕНТУ АБО ЗА ДОПОМОГОЮ КРІПЛЕННЯ ШУРУПАМИ, ЩО ЙДУТЬ У КОМПЛЕКТІ.

Вертикальне встановлення

  1. Встановіть та закріпіть магніт
  2. Встановіть нижню пластину приладу
  3. Встановіть прилад в нижню пластину

Горизонтальне встановлення

  1. Встановіть та закріпіть магніт
  2. Встановіть нижню пластину приладу
  3. Встановіть прилад в нижню пластину

УВАГА! ПРИ ПРАВИЛЬНОМУ ВСТАНОВЛЕННІ ПРИЛАДУ ТАМПЕР БУДЕ ЗАТИСНУТО (ЗАФІКСОВАНО).

Підключення зовнішнього датчика

Використовується в випадках, коли встановлення U-Prox WDC неможливе, потрібний прихований монтаж або для обробки сигналів від іншого зовнішнього датчика чи пристрою.

Підключення зовнішнього світлодіода

Зовнішній світлодіод використовується для світлового підтвердження того, що група охорони була взята під охорону, подія про це доставлена до охоронної компанії чи хмари U-Prox, і охоронний центр отримав підтвердження про доставку події.

Світлодіод вмикається на час до 15 секунд після порушення та відновлення датчику під час відліку затримки на вихід.

Ввімкнення та вимкнення

Перемістіть перемикач в положення ON — світловий індикатор буде ввімкнено. Якщо прилад вже було зареєстровано в охоронній системі, він переходить до чергового режиму. Щоб вимкнути прилад, перемістіть перемикач в положення OFF

УВАГА. ЯКЩО ПРИЛАД НЕ БУЛО ЗАРЕЄСТРОВАНО, ЧЕРЕЗ 30 СЕКУНД ВІН ПЕРЕЙДЕ В РЕЖИМ СНУ.

Налаштування

  1. Завантажте і встановіть мобільний додаток для налаштування системи U-Prox Installer
  2. Запустіть додаток U-Prox Installer та ввійдіть в систему або увійдіть за допомого вебпорталу U-Prox Installer WEB

При необхідності зареєструйтесь в системі як автономний інсталятор або отримайте доступ як інсталятор охоронної компанії

Додавання пристрою до охоронної системи (реєстрація)

  1. Запустіть додаток U-Prox Installer чи відкрийте в браузері вебпортал та ввійдіть в систему
  2. Оберіть зі списку приладів U-Prox MPX, до якого потрібно додати бездротовий датчик
  3. Натисніть кнопку (+) («Додати радіопристрій»), охоронний центр перейде в режим реєстрації сповіщувачів, клавіатур тощо. У цьому вікні можна натиснути іконки пристроїв і переглянути інструкції по включенню.
  4. Відповідно до інструкції ввімкніть бездротовий датчик та піднесіть його до охоронного центру на відстань близько 1 метра
  5. Зачекайте 15-20 секунд – бездротовий датчик буде зареєстровано
  6. В додатку будуть відкриті налаштування бездротового датчика
  7. Виконайте налаштування пристрою

Увага! Пристрій буде додано в першу вільну зону з найменшим номером

 

Питання та відповіді

Filter
  • Everything that is in U-PROX, from the idea to the engineering implementation is done exclusively in Ukraine.

  • Most of the sensors are powered by lithium batteries. They have sufficient capacity and operating temperature range.

    Thanks to the adaptive power of the radio transmitters and the optimized data transmission protocol, the service life can be up to 7 years. The shortest service life of alkaline batteries “finger” or AAA, which are installed in the keyboard – up to 2 years.

    But the replacement does not even require a screwdriver, the keyboard is removed using a regular plastic discount or bank card.

  • 15 years ago massively used wired phones, mobile phones were either business or luxury. Now almost everyone has mobile phones. It’s not only comfortable. The quality of wireless communication is steadily increasing.

    The same situation with security systems. Wired systems require high-quality cable, trained personnel with electrical education, quality installation with line inspection, construction work with drilling, wiring, and other inconveniences. All this requires a lot of time.

    As a result, we have a total cost which includes work. And compared with wireless systems, it is much higher. The wireless security system can be installed independently, the kit includes everything you need for installation.

    The U-PROX security system has U-PROX BAND radio communication technology. It has unsurpassed characteristics in range, resistance to interference, due to channel redundancy, and is very efficient in terms of energy consumption.

  • It is reliable communication that distinguishes the U-PROX security system from its competitors. We use DSTU GOST28147-89 encryption with reverse gamma, 256-bit key (3DES level).
    Any of our radio devices operates in the notification (notification) mode, not polling, that is, as soon as an event occurs, it is immediately transmitted to U-PROX. In turn, the security center confirms the reception of the data packet by sending a response. The communication is two-way, imitation-resistant: the packet contains the detector serial number and the packet sequence number, which makes it impossible to replace the detector or send the same data packet by an intruder.

    The detector periodically sends data about its status to U-PROX, notifying that it is “alive”. We call this a “heartbit”. In response, it receives confirmation and additional commands.

    If the detector is installed in a place with poor conditions, it is used:

    • increasing the radio communication power – 3 gradations of the transmitting device power are available,
    • switching the data rate to improve the sensitivity of the receiving path,
    • switching to other (backup) channels in the frequency range of 868.0 … 868.6 MHz.

    In turn, the basic U-PROX device has 2 transceivers that work simultaneously to receive signals on different channels and speeds. And of course, there is a definition of radio jamming.

  • Your device communicates with the security company via two GPRS/LTE channels and the Internet – Wi-Fi or Ethernet.

    If you try to “jam” or somehow block the communication channel, U-PROX will send a signal about it.

  • Yes, if the security system uses the U-PROX PIR Cam detector with photo fixation.

    Thanks to it, users of the U-PROX Home mobile application can receive a photo from the detector at any time by pressing one button.

    Also, when a photo is received on request, it is possible to save it to the user’s smartphone photo gallery and enlarge it if necessary.

    The owner of the security system can also configure permissions to send photos in case of alarm to security companies.

  • Wi-Fi is a wireless technology for connecting devices to the wired Internet.

    It is implemented in the all security centers (hubs).

    The central unit in this case can be placed anywhere.

    1. We believe that this is our future – in 2-3 years, wireless equipment will occupy a large part of the security systems market. Almost everything will be wireless, and prices for such solutions will decrease.
    2. Wireless solutions are fast, convenient, and reliable.
    3. Вo not spoil the interior design and renovation during installation, as require a minimum of installation work.
    4. Minimize the time spent on installing the security system.
    5. U-PROX WDC, U-PROX Wireport, U-PROX Multiplexer  and U-PROX Siren have wired inputs to which wired devices can also be connected.
  • The use of mobile applications U-PROX Home and U-PROX Installer allowed to separate system settings and management.

    The U-PROX Home application is used to control the U-PROX security system. The application implements the required set of functions:

    • Arming.
    • Disarming.
    • Arming in night mode.
    • Alarm button.
    • Event history with simple filters.
    • View temperature from sensors.
    • Add camcorders with zones.
    • Watch the video from a connected camera.
    • In the event of any failure in the system application, U-PROX brings this information to the home screen, and notify the user via Push message.

    U-PROX Installer is used to configure the security system. Through an application is performed the primary activation of the sensors

  • The security group is a logically independent unit in the security system.

    It combines a group of sensors, which is placed and removed from protection separately and independently of others.

    This can be done by a user who is authorized to manage a specific group.

  • This is a function that can work in any of the security groups.

    It is implemented as follows. Consider the example of the house. When people put guards in this mode, the sensors that protect the perimeter: doors, windows, or even the entire first floor – become active. Other sensors – indoors – inactive. So, you can move freely inside the room, and intrusion from the outside will be detected.

  • The sensors are powered by their own batteries.

    And the U-PROX security center is equipped with a lithium-ion battery, which will provide autonomous power for 24 hours.

    And if this is not enough, then you can use the design feature of U-PROX devices – an input power supply 12V DC, which means that an external uninterruptible power supply can be used, or a car battery, then the autonomous life can be increased, even up to several weeks.

  • It is very easy to install the U-PROX security system. Everything you need for installation: screws, fasteners, come complete with each sensor. The devices have simple mounts. Installation of the sensors to the required space can be done using screws or using two-way tape.

    The overall security system installation will take about 10-15 minutes.It is very easy to install the U-PROX security system.

    Everything you need for installation: screws, fasteners, come complete with each sensor. The devices have simple mounts.

    Installation of the sensors to the required space can be done using screws or using two-way tape.

    The overall security system installation will take about 10-15 minutes.

    1. Modern energy-saving technologies allow you to not think about replacing batteries for several years (2-7 years).
    2. 2 weeks before the full discharge, the security system will warn you and the service security organization about the discharge.
    3. Popular battery sizes are used ААА, CR2, CR123A і CR2032.
  • This is implemented using cloud technology.

    With the security panel, the system works directly, “without intermediaries”.

    With the user’s smartphone, the mediator is the cell of the device in the cloud, through which events are displayed on the smartphone and control commands from the user are passed.

  • Modern systems work via an Internet connection, this is mobile Internet in LTE networks or fixed cable.

    U-PROX uses both connections, thus providing data transmission redundancy to the monitoring station in case of blocking or jamming of GSM-communication or cable breakage.

    Control of communication with the device is provided by the monitoring panel.

  • You can prevent water leaks in your apartment or house thanks to automation devices from U-PROX. The flood prevention system warns you of an unwanted water leak in the U-PROX Home app and automatically shuts off the water supply in case of a pipe burst or a malfunction of the washing machine.

    The smart valve control and power supply device allows you to automatically shut off/open the water supply when arming/disarming the room.

    You can also create personalized schedules for arming/disarming/operating the relay/water valve.

  • We use a proprietary technology called “U-PROX BAND”, it operates in the 868.0-868.6 MHz frequency range allocated for such systems and transmitter powers allowed without licensing up to 25 MW in the basic device, up to 20 mW in detectors, 10 mW in key fobs, with dynamic adjustment (the first exchange attempt is always at minimum power).

    U-PROX BAND has significant advantages over its competitors: the length of the packets transmitted over the air is almost two times less, the optimized retry algorithm (this is energy consumption), the sensitivity of the detector receivers is higher (this is the range both in line of sight and in building conditions). The U-PROX security center has two transceivers operating at different frequencies in the permitted range, providing redundant data transmission from sensors.

    One of the “tricks” of U-PROX BAND is the function of updating the software of all elements over the air. If any shortcomings are corrected or the functionality of the device is added, then the owner and the security company do not need to worry about dismantling, sending for an update. The update will occur automatically after the automatic update of the basic device.

  • The U-PROX security system has a refined design.

    As standard, the case of devices is executed in white or black color.

    For WDC sensors, the white starter kit includes replaceable dark brown housings.

  • If the animal is no more than 25 kg, then we will install special sensors that do not react to such animals, it is not required to restrict pets in movement.

    If the animal is large, then we recommend allocating a space for it in the room, where sensors that react to movement will not be installed, there you can install a sensor that responds to glass breakage, or sensors for opening doors and windows.

  • You can install the U-PROX Security System even if you have no wired internet.

    Since the backup communication source is the LTE/GSM network (the mobile operator card is installed).

    But in this case, you lose one of the communication channels.

  • If the phone is out of network, the security system remote control and watch events will not work.

    But you can get an alarm notification if you set up a call from the device to the user’s phone. This mode is indispensable if the system operates autonomously, without remote monitoring.

    We advise you to entrust security only to specialized companies, which will monitor your facility 24/7 and respond in case of alarm notification.

    U-PROX is the best wireless device for remote protection.

Still have questions? Can't find the answer you're looking for?